Revision Library
Choose a subject
Menu
Higher Tier - Year 10

Year 10 Paper 4: Matter and Motion

Covers energy stores and transfers, electrical circuits, domestic electricity and power, the particle model of matter, atomic structure, and forces and motion.

12 questions - 60 marks - calculator allowed

Year 10 follows a typical teaching order. No exam board defines what belongs to Year 10, and schools sequence the course differently. Check it against your own scheme of work before using it to decide what a class has covered.

Download PDF

Open GCSE Physics workspace

Questions

Question 1 [4 marks]

Domestic Electricity and Power

An electric shower has a power rating of 8.5 kW and is connected to the 230 V mains supply.

Calculate the current drawn by the shower, and state, with a reason, whether a 13 A fuse would be suitable for this appliance.

Question 2 [4 marks]

Particle Model of Matter

A sealed, rigid container holds a fixed mass of gas. The gas is cooled while the volume of the container stays constant.

Use the particle model to explain why the pressure of the gas decreases as its temperature decreases at constant volume.

Question 3 [5 marks]

Atomic Structure and Radioactivity

The accepted model of the atom has changed as new experimental evidence has been obtained.

Describe how the discovery of the neutron, and earlier experimental evidence such as the alpha particle scattering experiment, changed the accepted model of the atom over time.

Question 4 [5 marks]

Electrical Circuits and Components

A 15 ohm resistor and a 25 ohm resistor are connected in series with an 8 V battery.

Calculate the total resistance of the circuit, the current flowing through the circuit, and the potential difference across the 15 ohm resistor.

Question 5 [5 marks]

Energy Stores, Transfers and Conservation

A 2 kg block of copper is initially at 150 deg C and cools down, releasing 30,800 J of energy to the surroundings. The specific heat capacity of copper is 385 J/kg deg C.

Calculate the fall in temperature of the block, and hence calculate its final temperature.

Question 6 [5 marks]

Forces, Motion and Newton's Laws

A tractor pulls a trailer using a driving force of 3200 N. Friction and air resistance act on the trailer with a total resistive force of 800 N in the opposite direction. The trailer has a mass of 1200 kg.

Calculate the resultant force on the trailer, and its acceleration.

Question 7 [4 marks]

Electrical Circuits and Components

A student investigates the current against potential difference characteristic of a fixed resistor kept at constant temperature, and compares it with that of a filament lamp.

Describe the current against potential difference graphs for the fixed resistor and the filament lamp. Explain the shape of the filament lamp graph in terms of heating and the movement of particles.

Question 8 [5 marks]

Domestic Electricity and Power

A student compares two appliances in her home: an LED lamp rated at 9 W and an old filament lamp rated at 60 W, which produce a similar amount of useful light output.

Explain, in terms of energy transfers, why the LED lamp is more efficient than the filament lamp, and explain why replacing filament lamps with LED lamps can reduce a household's electricity costs and its impact on the environment, even though LED lamps are usually more expensive to buy.

Question 9 [5 marks]

Forces, Motion and Newton's Laws

A car's braking distance depends on its speed when the brakes are applied.

Explain, using the ideas of kinetic energy and the work done by the braking force, why doubling a car's speed increases its braking distance by a factor of four, assuming the braking force stays the same.

Question 10 [6 marks]

Energy Stores, Transfers and Conservation

A washing machine motor is supplied with 1200 J of electrical energy every second. Of this, 900 J is usefully transferred to the kinetic energy store of the drum, and the rest is wasted, dissipated to the thermal energy store of the surroundings.

Calculate the efficiency of the motor as a percentage. The manufacturer then redesigns the motor so that only 180 J is wasted every second for the same 1200 J of input energy each second. Calculate the new efficiency, and state by how many percentage points the efficiency has improved.

Question 11 [6 marks]

Atomic Structure and Radioactivity

Radium-226 (atomic number 88) decays by alpha emission to form an isotope of radon (Rn).

Determine the mass number and atomic number of the radon nucleus produced, explaining each change, and write a word equation for this decay. Then calculate the number of neutrons in the radon nucleus formed.

Question 12 [6 marks]

Energy Stores, Transfers and Conservation

An immersion heater rated at 2100 W is used to heat 3 kg of water, initially at 18 deg C, for 150 s. The heater is only 80% efficient; the rest of the input energy is lost to the surroundings rather than heating the water. The specific heat capacity of water is 4200 J/kg deg C.

Calculate the total energy supplied to the heater, the useful energy transferred to the water, and hence the final temperature of the water, assuming no further heat loss from the water.

Model solutions

Mark scheme for Question 1 [4 marks]
Question 1[4 marks]
Answer or workingMarks
current = power / potential differenceM1
substituting 8500 / 230M1
current = 37.0 A (accept 36.9-37.0 A)A1
stating a 13 A fuse is not suitable because the operating current (37 A) is greater than 13 A, so it would blow during normal useB1
Final answer: 37.0 A (36.96 A); a 13 A fuse is not suitable because the operating current exceeds 13 A.
Mark scheme for Question 2 [4 marks]
Question 2[4 marks]
Answer or workingMarks
stating cooling the gas decreases the average kinetic energy of the gas particles, so on average they move slowerB1
stating the particles collide with the walls of the container less often per secondB1
a smaller average change in particle momentum in each wall collisionB1
linking the rate of momentum transfer to force on the wall, and pressure to force per unit areaB1
Final answer: Cooling decreases average particle kinetic energy. Particles move slower and collide with the walls less often, with a smaller momentum change per collision. The rate of momentum transfer, hence the force on the walls and the pressure (force per unit area), decreases.
Mark scheme for Question 3 [5 marks]
Question 3[5 marks]
Answer or workingMarks
describing the earlier 'plum pudding' model, in which the atom was a ball of positive charge with electrons embedded in itB1
describing that in the alpha scattering experiment most alpha particles passed straight through a thin gold foil, but a small number were deflected by large angles or bounced backB1
explaining this showed most of the atom is empty space, and that there must be a small, dense, positively charged region, the nucleus, at the centre of the atomB1
describing that this evidence led to the nuclear model, later refined by Bohr to show electrons orbit the nucleus at specific distances in shellsB1
describing the later discovery of the neutron, which explained the mass of the nucleus not being accounted for by protons aloneB1
Final answer: The plum-pudding model had electrons embedded in distributed positive charge. Most alpha particles passed straight through thin foil, while a small number were deflected through large angles or bounced back. This showed the atom is mostly empty space with a tiny, dense, positive nucleus. Bohr refined the nuclear model with electrons in discrete shells at specified distances. Discovery of neutrons in the nucleus explained nuclear mass not accounted for by protons alone.
Mark scheme for Question 4 [5 marks]
Question 4[5 marks]
Answer or workingMarks
total resistance in series = sum of the individual resistances = 15 + 25M1
total resistance = 40 ohmA1
current = potential difference / total resistance = 8 / 40M1
current = 0.2 AA1
potential difference across the 15 ohm resistor = current x resistance = 0.2 x 15 = 3 VB1
Final answer: Total resistance = 40 ohm; current = 0.2 A; potential difference across the 15 ohm resistor = 3 V.
Mark scheme for Question 5 [5 marks]
Question 5[5 marks]
Answer or workingMarks
change in temperature = energy transferred / (mass x specific heat capacity)M1
substituting 30800 / (2 x 385)M1
change in temperature = 40 deg CA1
final temperature = 150 - 40M1
final temperature = 110 deg CA1
Final answer: Fall in temperature = 40 deg C; final temperature = 110 deg C.
Mark scheme for Question 6 [5 marks]
Question 6[5 marks]
Answer or workingMarks
resultant force = driving force - resistive forces = 3200 - 800M1
resultant force = 2400 NA1
acceleration = resultant force / massM1
substituting 2400 / 1200M1
acceleration = 2 m/s^2A1
Final answer: Resultant force = 2400 N; acceleration = 2 m/s^2.
Mark scheme for Question 7 [4 marks]
Question 7[4 marks]
Answer or workingMarks
the fixed resistor having a straight I-V line through the originB1
the lamp curve passing through the origin and becoming shallower as the magnitude of potential difference increasesB1
explaining current heats the filamentB1
explaining hotter lattice ions vibrate more strongly, causing more electron scattering and increased resistanceB1
Final answer: The fixed resistor has a straight I-V line through the origin. The lamp curve passes through the origin and becomes shallower as the magnitude of potential difference increases. Current heats the filament; greater lattice vibrations cause more electron scattering and increased resistance.
Mark scheme for Question 8 [5 marks]
Question 8[5 marks]
Answer or workingMarks
explaining the filament lamp wastes much more energy, transferring it to the thermal energy store of the surroundings (it gets much hotter), than the LED lamp for the same light outputB1
stating this means a greater proportion of the LED lamp's input energy transfer is a useful output, so it has a higher efficiencyB1
explaining the LED lamp uses much less power for the same light output, so transfers less energy over time, reducing electricity bills over the lamp's lifetime despite its higher purchase costB1
explaining that using less electrical energy means less energy needs to be generated at power stationsB1
explaining that where this generation involves burning fossil fuels, using less energy reduces the amount of harmful or greenhouse gases released, reducing environmental impactB1
Final answer: For the same useful light output the LED wastes less energy heating the surroundings, so a larger fraction of its electrical input is useful. Lower power for the same usage time means lower energy use and running costs, which can offset the higher purchase price over time. Less electricity needs to be generated; if this displaces fossil-fuel generation, fuel use and emissions fall.
Mark scheme for Question 9 [5 marks]
Question 9[5 marks]
Answer or workingMarks
kinetic energy = 0.5 x mass x speed^2B1
using the square dependence to show doubling speed quadruples kinetic energy for the same massB1
work done against the braking force = braking force magnitude x braking distanceB1
explaining that the work done against the braking force equals the initial kinetic energy removed in stoppingB1
deducing from distance = kinetic energy / braking force that four times the energy requires four times the braking distance at the same constant forceB1
Final answer: Kinetic energy is proportional to speed squared, so doubling speed quadruples it; since work done by a constant braking force (force x distance) must remove this kinetic energy, the braking distance also increases by a factor of four.
Mark scheme for Question 10 [6 marks]
Question 10[6 marks]
Answer or workingMarks
original efficiency = useful output energy transfer / total input energy transferM1
substituting 900 / 1200M1
original efficiency = 75%A1
new useful output = 1200 - 180 (= 1020 J)M1
new efficiency = 1020 / 1200 = 85%A1
stating the efficiency has improved by 10 percentage pointsB1
Final answer: Original efficiency = 75%; new efficiency = 85%; an improvement of 10 percentage points.
Mark scheme for Question 11 [6 marks]
Question 11[6 marks]
Answer or workingMarks
mass number of radon = 226 - 4 (the mass number of the alpha particle)M1
mass number of radon = 222A1
atomic number of radon = 88 - 2 (the atomic number of the alpha particle)M1
atomic number of radon = 86A1
the word equation: radium-226 -> radon-222 + alpha particle; accept a balanced nuclide-symbol equationB1
neutrons in the radon nucleus = mass number - atomic number = 222 - 86 = 136B1
Final answer: An alpha particle carries away four nucleons, so mass number = 226 - 4 = 222. It carries away two protons, so atomic number = 88 - 2 = 86. Radium-226 -> radon-222 + alpha particle. Neutrons in radon = 222 - 86 = 136.
Mark scheme for Question 12 [6 marks]
Question 12[6 marks]
Answer or workingMarks
total input energy = power x time = 2100 x 150M1
total input energy = 315000 JA1
useful energy transferred to the water = efficiency x total input energy = 0.8 x 315000M1
useful energy = 252000 JA1
rearranging useful energy = m c (change in temperature) to change in temperature = 252000 / (3 x 4200)M1
change in temperature = 20 deg C, so final temperature = 18 + 20 = 38 deg CA1
Final answer: Total input energy = 315000 J; useful energy = 252000 J; final temperature of the water = 38 deg C.

Build a free practice pack.

Pick the topics, add the student's name and print one PDF.