Year 10 Paper 5: Energy and Atoms
Covers energy stores and transfers, energy resources and efficiency, domestic electricity and power, the particle model of matter, atomic structure, and forces and motion.
Year 10 follows a typical teaching order. No exam board defines what belongs to Year 10, and schools sequence the course differently. Check it against your own scheme of work before using it to decide what a class has covered.
Questions
Question 1 [4 marks]
Particle Model of Matter
A sealed container holds a fixed mass of gas. The gas is heated while the volume of the container stays constant.
Use the particle model to explain why the pressure of the gas increases as its temperature increases at constant volume.
Question 2 [4 marks]
Atomic Structure and Radioactivity
A sample of a radioactive isotope has an initial net count rate of 960 counts per minute, after background radiation has been subtracted. The detector conditions remain unchanged. The isotope has a half-life of 5 hours.
Calculate the net count rate after 20 hours, and state what is meant by half-life.
Question 3 [4 marks]
Domestic Electricity and Power
A washing machine has a power rating of 2300 W and is connected to the 230 V mains supply.
Calculate the current drawn by the washing machine, and state, with a reason, whether a 5 A fuse would be suitable for this appliance.
Question 4 [4 marks]
Energy Resources and Efficiency
A student wants to reduce the electrical energy used by an old refrigerator to maintain the same internal temperature. Heat enters through its casing, and friction in its compressor motor dissipates some input energy.
Describe two methods that could be used to reduce this waste, and explain how each method increases the refrigerator's efficiency.
Question 5 [5 marks]
Energy Stores, Transfers and Conservation
A 2 kg block of copper is initially at 150 deg C and cools down, releasing 30,800 J of energy to the surroundings. The specific heat capacity of copper is 385 J/kg deg C.
Calculate the fall in temperature of the block, and hence calculate its final temperature.
Question 6 [5 marks]
Forces, Motion and Newton's Laws
A tractor pulls a trailer using a driving force of 3200 N. Friction and air resistance act on the trailer with a total resistive force of 800 N in the opposite direction. The trailer has a mass of 1200 kg.
Calculate the resultant force on the trailer, and its acceleration.
Question 7 [5 marks]
Particle Model of Matter
A fixed mass of gas is sealed in a cylinder with a volume of 0.020 m^3 at a pressure of 100,000 Pa. The gas is slowly compressed at constant temperature until its volume is 0.008 m^3.
Calculate the new pressure of the gas. Explain using the particle model why the pressure increases at constant temperature.
Question 8 [5 marks]
Atomic Structure and Radioactivity
An isotope with a half-life of 15 days is injected into an underground pipeline to detect a leak. The isotope has an initial activity of 640 MBq. The planned survey lasts several weeks.
Calculate the activity of the sample after 60 days. Then explain why an isotope with a half-life of a few weeks, rather than a few hours or several thousand years, is chosen for this purpose.
Question 9 [6 marks]
Energy Stores, Transfers and Conservation
An immersion heater rated at 2100 W is used to heat 3 kg of water, initially at 18 deg C, for 150 s. The heater is only 80% efficient; the rest of the input energy is lost to the surroundings rather than heating the water. The specific heat capacity of water is 4200 J/kg deg C.
Calculate the total energy supplied to the heater, the useful energy transferred to the water, and hence the final temperature of the water, assuming no further heat loss from the water.
Question 10 [6 marks]
Domestic Electricity and Power
A kettle is rated at 230 V, 2760 W. Fuses are available in 3 A, 5 A and 13 A ratings.
Calculate the normal operating current of the kettle, and determine which of the available fuses should be fitted. Explain why the chosen fuse rating should be only a little higher than the normal operating current, rather than much higher.
Question 11 [6 marks]
Forces, Motion and Newton's Laws
A car's overall stopping distance is made up of the thinking distance and the braking distance.
Explain what is meant by thinking distance and braking distance, and describe one factor that increases each of these distances, explaining why.
Question 12 [6 marks]
Energy Stores, Transfers and Conservation
A pendulum bob of mass 0.25 kg is pulled to one side and released so that it swings. At the highest point of its swing it is 0.08 m above its lowest point. Assume air resistance is negligible for this calculation. Gravitational field strength g = 9.8 N/kg.
Calculate the maximum speed of the pendulum bob as it passes through its lowest point. Then state what happens to the energy stores of the pendulum as it continues to swing if air resistance is not negligible. State how the maximum height and speed of successive swings change.
Model solutions
| Question 1[4 marks] | |
|---|---|
| Answer or working | Marks |
| stating heating the gas increases the average kinetic energy of the gas particles, so on average they move faster | B1 |
| stating the particles collide with the walls of the container more often per second | B1 |
| a larger average change in particle momentum in each wall collision | B1 |
| linking the rate of momentum transfer to force on the wall, and pressure to force per unit area | B1 |
| Final answer: Heating increases average particle kinetic energy. Particles move faster and collide with the walls more often, with a larger momentum change per collision. The rate of momentum transfer, hence the force on the walls and the pressure (force per unit area), increases. | |
| Question 2[4 marks] | |
|---|---|
| Answer or working | Marks |
| number of half-lives elapsed = 20 / 5 = 4 | M1 |
| halving the count rate four times: 960, then 480, then 240, then 120, then 60 | M1 |
| count rate = 60 counts per minute | A1 |
| stating half-life is the time taken for the number of undecayed parent nuclei, mass of the parent isotope remaining, or activity to halve; accept background-corrected count rate halving with unchanged detector conditions | A1 |
| Final answer: 60 counts per minute. Half-life is the time taken for the number of undecayed parent nuclei, or their activity, to halve. | |
| Question 3[4 marks] | |
|---|---|
| Answer or working | Marks |
| current = power / potential difference | M1 |
| substituting 2300 / 230 | M1 |
| current = 10 A | A1 |
| stating a 5 A fuse is not suitable because the operating current (10 A) is greater than 5 A, so it would blow during normal use | B1 |
| Final answer: 10 A; a 5 A fuse is not suitable because the operating current exceeds 5 A. | |
| Question 4[4 marks] | |
|---|---|
| Answer or working | Marks |
| improving the casing insulation | B1 |
| explaining that less heat enters from the warmer surroundings, so less compressor operation is needed for the same temperature | B1 |
| lubricating the compressor bearings or another valid method of reducing compressor losses | B1 |
| explaining how that method reduces losses, such as less frictional heating for the same cooling; accept two other distinct valid methods with their corresponding explanations | B1 |
| Final answer: Improve the casing insulation to reduce heat entering from the warmer surroundings, so the compressor runs less to maintain the same internal temperature. Lubricate the compressor bearings to reduce friction and frictional heating, reducing electrical input for the same cooling. | |
| Question 5[5 marks] | |
|---|---|
| Answer or working | Marks |
| change in temperature = energy transferred / (mass x specific heat capacity) | M1 |
| substituting 30800 / (2 x 385) | M1 |
| change in temperature = 40 deg C | A1 |
| final temperature = 150 - 40 | M1 |
| final temperature = 110 deg C | A1 |
| Final answer: Fall in temperature = 40 deg C; final temperature = 110 deg C. | |
| Question 6[5 marks] | |
|---|---|
| Answer or working | Marks |
| resultant force = driving force - resistive forces = 3200 - 800 | M1 |
| resultant force = 2400 N | A1 |
| acceleration = resultant force / mass | M1 |
| substituting 2400 / 1200 | M1 |
| acceleration = 2 m/s^2 | A1 |
| Final answer: Resultant force = 2400 N; acceleration = 2 m/s^2. | |
| Question 7[5 marks] | |
|---|---|
| Answer or working | Marks |
| using pressure x volume = constant, at constant temperature | M1 |
| substituting p1 V1 = p2 V2, i.e. 100000 x 0.020 = p2 x 0.008 | M1 |
| rearranging to p2 = (100000 x 0.020) / 0.008 | M1 |
| new pressure = 250000 Pa (250 kPa) | A1 |
| explaining that doing work on the gas to compress it increases the frequency of collisions between particles and the container walls without changing the particles' average speed | B1 |
| Final answer: 250000 Pa (250 kPa) At constant temperature average particle speed is unchanged, but compression increases the number of collisions per unit wall area per second, increasing pressure. | |
| Question 8[5 marks] | |
|---|---|
| Answer or working | Marks |
| number of half-lives = 60 / 15 = 4 | M1 |
| halving the activity four times: 640, then 320, then 160, then 80, then 40 | M1 |
| activity = 40 MBq | A1 |
| stating an isotope with a half-life of only a few hours would decay away before the leak survey could be completed | B1 |
| stating an isotope with a half-life of thousands of years would remain radioactive, and hazardous, in the environment for far longer than necessary | B1 |
| Final answer: 40 MBq. A half-life of a few weeks keeps activity detectable during the stated survey. A few hours would allow activity to fall too far before it finishes, while thousands of years would leave unnecessary long-term radioactive material. Activity falls more quickly afterwards, but half-life alone does not establish safety. | |
| Question 9[6 marks] | |
|---|---|
| Answer or working | Marks |
| total input energy = power x time = 2100 x 150 | M1 |
| total input energy = 315000 J | A1 |
| useful energy transferred to the water = efficiency x total input energy = 0.8 x 315000 | M1 |
| useful energy = 252000 J | A1 |
| rearranging useful energy = m c (change in temperature) to change in temperature = 252000 / (3 x 4200) | M1 |
| change in temperature = 20 deg C, so final temperature = 18 + 20 = 38 deg C | A1 |
| Final answer: Total input energy = 315000 J; useful energy = 252000 J; final temperature of the water = 38 deg C. | |
| Question 10[6 marks] | |
|---|---|
| Answer or working | Marks |
| current = power / potential difference | M1 |
| substituting 2760 / 230 | M1 |
| current = 12 A | A1 |
| selecting the 13 A fuse, because it is the only rating higher than the normal operating current (a 5 A fuse would blow during normal use) | B1 |
| explaining the fuse rating should be only a little higher than the normal operating current so that it still blows quickly if a fault causes the current to become dangerously large | B1 |
| explaining that a sustained excessive current heats the wiring and can damage insulation or cause a fire | B1 |
| Final answer: Current = 2760 / 230 = 12 A. Choose the 13 A fuse, the lowest available rating above normal current. It permits normal operation but disconnects if current becomes excessive. A much higher rating can allow an overload to persist, heating the wiring and potentially damaging insulation or causing a fire. | |
| Question 11[6 marks] | |
|---|---|
| Answer or working | Marks |
| thinking distance being the distance the car travels during the driver's reaction time, before the brakes are applied | B1 |
| braking distance being the distance the car travels while decelerating, from when the brakes are applied to when the car stops | B1 |
| a factor increasing thinking distance, such as tiredness, alcohol/drugs, or distractions such as using a mobile phone | B1 |
| explaining this factor increases the driver's reaction time, so the car travels further before the brakes are applied | B1 |
| a factor increasing braking distance, such as a wet or icy road, worn brakes or worn tyres, or the car travelling faster | B1 |
| explaining this factor reduces the friction (grip) between the tyres and the road, or reduces the braking force available, so a greater distance is needed to bring the car to rest; for higher initial speed, explain the greater kinetic energy requiring more work to stop at the same braking force | B1 |
| Final answer: Thinking distance is the distance travelled during the driver's reaction time before braking; braking distance is the distance travelled while decelerating to a stop. Tiredness or distraction increases thinking distance by lengthening reaction time; a wet road or worn tyres increases braking distance by reducing grip/friction. | |
| Question 12[6 marks] | |
|---|---|
| Answer or working | Marks |
| GPE at the highest point = m g h = 0.25 x 9.8 x 0.08 | M1 |
| GPE = 0.196 J | A1 |
| using 1/2 m v^2 = 0.196 to find v^2 = 2 x 0.196 / 0.25 (= 1.568) | M1 |
| v = 1.25 m/s | A1 |
| stating some energy is transferred to the thermal energy store of the surroundings by air resistance (it is dissipated) | B1 |
| stating the maximum height, and therefore maximum speed, of each swing decreases over time as a result | B1 |
| Final answer: v = 1.25 m/s; energy is dissipated to the thermal store of the surroundings by air resistance, so each swing reaches a lower maximum height and speed. | |