Revision Library
Choose a subject
Menu
Science
Need a new topic?
Missing a topic, found a bug, or want something added?
KS3 Science · Topic guide

Working Scientifically: Measuring, Recording and Risk

Good science depends on measuring carefully, recording honestly and working safely. Choose the instrument that fits the job: a measuring cylinder for volume, a balance for mass, a thermometer for temperature, a ruler for length and a stopwatch for time. Its resolution is the smallest division it can show, and you should record readings to that resolution with the same number of decimal places each time. Use SI units and convert between them correctly: 1 kg = 1000 g, 1 cm3 = 1 ml, 1 dm3 = 1000 cm3 (1 litre), 1 min = 60 s, and 1 cm = 10 mm, 1 m = 100 cm = 1000 mm. Watch for zero error, where an instrument does not read zero when it should, and parallax, where reading a scale from the side gives a wrong value. Read a liquid in a measuring cylinder with your eye level with the bottom of the curved surface, the meniscus. Accuracy means close to the true value; precision means repeat readings are close to each other. Observations describe what you see in words; measurements give numbers with units. Record results in a table with the independent variable in the first column, the quantity and unit in each heading and not in the cells, and a mean that excludes a reading only with a stated reason, recording which reading was excluded and why. A hazard is something that could cause harm; the risk is how likely that harm is and how serious. A control measure is chosen to fit the hazard, and a short risk assessment lists the hazard, the harm, and the control for each part of a practical.

Year 7-9 (KS3)Working ScientificallyNational Curriculum

Before you start

Make sure you're comfortable with these topics first:

Method

  1. Pick the instrument for the quantity and check its range and resolution. A 100 cm3 measuring cylinder marked every 1 cm3 can be read to the nearest 1 cm3, so record whole numbers such as 36 cm3, not 36.0 cm3.
  2. Check for zero error before you start: a balance should read 0.0 g when empty (use the tare button or subtract the offset), and a ruler's end should not be worn away. Say how you dealt with it.
  3. Read the scale properly. Put your eye level with the scale to avoid parallax, and for a liquid in a measuring cylinder read the bottom of the meniscus on a flat surface.
  4. Convert units before you compare or calculate. To go from a larger unit to a smaller one multiply (kg to g: x 1000); to go from a smaller unit to a larger one divide (cm3 to dm3: / 1000; s to min: / 60; mm to cm: / 10).
  5. Record observations in words (colour change, bubbles, a solid dissolving) and measurements in a results table: independent variable first, units in the heading only, and the same number of decimal places down each column. Never taste anything, and only smell a substance by wafting the vapour towards you if told to.
  6. Repeat each measurement at least three times. Investigate an unusual reading and repeat the measurement where possible. Exclude it only with a stated justification, recording which result was excluded and why. Calculate the mean by adding the retained readings and dividing by how many there are.
  7. Write a short risk assessment before you start. For each hazard give the harm it could cause and a control measure that fits it, for example eye protection for acids, a heatproof mat and tied-back hair when heating, and keeping water away from electrical equipment.

Common mistakes

  • MistakePutting the unit in every cell of a results table, for example '34 s', '37 s', '41 s'.

    InsteadPut the quantity and unit in the heading, for example Time (s), and write only numbers in the cells.

  • MistakeReading a measuring cylinder from above, or at the top edge of the meniscus.

    InsteadPut your eye level with the scale and read the bottom of the curved surface, with the cylinder standing on a flat bench.

  • MistakeWriting 'wear goggles' for every practical without saying what harm they prevent.

    InsteadName the hazard, say what harm it could do, then write the control that fits it: eye protection for acid splashes, a heatproof mat for hot beakers, dry hands and leads for electricity.

  • MistakeMixing up the conversions, for example saying 1 dm3 is 100 cm3 or dividing when you should multiply.

    InsteadRemember 1 dm3 = 1000 cm3 and 1 kg = 1000 g. Changing to a smaller unit gives a bigger number, so multiply; changing to a larger unit gives a smaller number, so divide.

Worked example

A pupil finds the mass of a wet sponge four times on a balance. Before the sponge is placed on it, the balance reads 0.3 g. The readings with the sponge on are 48.5 g, 48.7 g, 52.2 g and 48.6 g. (a) Correct for the zero error. (b) Identify the anomaly and calculate the mean mass of the sponge, leaving it out. (c) Give the mean in kg. (d) Convert a volume of 25 cm3 of water the sponge soaked up to dm3.

  1. The balance reads 0.3 g with nothing on it, so every reading is 0.3 g too high. Subtract 0.3 g from each reading: 48.2 g, 48.4 g, 51.9 g and 48.3 g.
  2. The readings 48.2, 48.4 and 48.3 are close together, but 51.9 g is far from them. The anomaly is 51.9 g (the sponge may have been dripping or the reading taken too early).
  3. Add the valid readings: 48.2 + 48.4 + 48.3 = 144.9 g.
  4. Divide by the number of valid readings: 144.9 / 3 = 48.3 g. This is the mean mass.
  5. Convert to kilograms by dividing by 1000: 48.3 / 1000 = 0.0483 kg.
  6. Convert the volume: 25 cm3 / 1000 = 0.025 dm3.
  7. Statement to write: the mean mass is 48.3 g (51.9 g excluded as an anomaly) after correcting for a zero error of 0.3 g.

Practice questions

Q1[1 mark]Convert 0.35 kg to grams.Show answer

Answer: 0.35 x 1000 = 350 g.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q2[1 mark]A beaker holds 2.5 dm3 of water. Give this volume in cm3.Show answer

Answer: 2.5 x 1000 = 2500 cm3.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q3[2 marks]Convert 45 mm into cm and into m.Show answer

Answer: 45 / 10 = 4.5 cm, and 4.5 / 100 = 0.045 m.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q4[1 mark]A pupil's stopwatch shows 150 s. Give this time in minutes.Show answer

Answer: 150 / 60 = 2.5 min.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q5[2 marks]A forcemeter is not hanging from anything and reads 0.2 N. Name this type of error and say what the pupil should do.Show answer

Answer: A zero error. Subtract 0.2 N from every reading, or adjust the scale back to zero before starting.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q6[2 marks]Explain why the pupil should read a measuring cylinder with their eye level with the meniscus.Show answer

Answer: Looking from above or below gives a parallax error, so the reading would be too high or too low. Reading at eye level with the bottom of the meniscus gives the correct volume.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q7[2 marks]A thermometer has marks every 1 degree Celsius. A pupil records a temperature as 23.46 degrees Celsius. Say what is wrong with this.Show answer

Answer: The reading has more decimal places than the resolution allows. It should be recorded to the nearest degree, for example 23 degrees Celsius.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q8[2 marks]Four repeat readings of a length are 6.1, 6.2, 6.1 and 6.2 cm, but the true length is 5.2 cm because the ruler has a worn end. Say whether the results are precise, accurate, both or neither.Show answer

Answer: Precise, because the repeats are close together, but not accurate, because they are not close to the true value.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q9[2 marks]Sort these into an observation and a measurement: 'the colour changed from blue to green' and '4.5 cm'.Show answer

Answer: Observation: the colour changed from blue to green (described in words). Measurement: 4.5 cm (a number with a unit from an instrument).

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.
Q10[3 marks]Explain the difference between a hazard and a risk using a Bunsen burner.Show answer

Answer: The hazard is the flame, which can burn skin or set things alight. The risk is how likely a burn or fire is and how serious it would be. A control measure such as a heatproof mat, tied-back hair and a yellow safety flame when not heating lowers the risk.

Got it right?
Your answerWork it out on paper, then show the answer and mark yourself.

Exam-style questions

Written in the style of a KS3 Science exam paper, with a full mark scheme.

Exam tips

  • Show the conversion or the mean working step by step, for example 144.9 / 3 = 48.3 g, and finish with the unit.
  • In a risk assessment, use a table with three columns: hazard, harm and control measure. Make each control fit its hazard.
  • If a question asks you to improve measurements, give a specific change such as a measuring cylinder instead of a beaker, a balance with a finer resolution, or taking readings at eye level.
Q1[7 marks]A pupil investigates how the volume of water affects how long it takes to heat to 40 degrees Celsius over a Bunsen burner. She heats 50, 100, 150 and 200 cm3 of water and records the time each time. Her table is headed: Volume of water | Time taken, with cells such as '50 cm3' and '34 s'. She repeats the 100 cm3 test three times and gets 71 s, 69 s and 94 s. (a) Rewrite the column headings correctly and say how the cells should change. (2) (b) Identify the anomaly in the 100 cm3 readings. (1) (c) Calculate the mean time for 100 cm3, leaving out the anomaly. (2) (d) Give two ways of reducing the risk when heating the water with a Bunsen burner. (2)Show mark scheme

Tick each line you got.

Nothing ticked yet - 7 available

Got it right?
Q2[6 marks]Write a short risk assessment for a practical in which pupils add dilute hydrochloric acid to marble chips in a conical flask, collect the gas and time it, with the stopwatch at a bench near a power pack. Your answer should name the hazards, say what harm each could cause and give a control measure that fits each hazard. Also say how the pupils will measure the 50 cm3 of acid accurately. (6)Show mark scheme

Tick each line you got.

Nothing ticked yet - 6 available

Got it right?

See real KS3 Science past-paper questions, with official mark schemes 

Free printable worksheet

Want more practice on paper? Download the Working Scientifically: Measuring, Recording and Risk worksheet pack - 7 pages of exam-style questions with a full mark scheme. Free to download, no card or account. Print it for personal and classroom use.

This worksheet is chapter 6 of KS3 Science Year 9 Topic Workbook, a free printable practice book.

Other versions of this worksheet:

Keep going

Not quite what you needed?

Tell us what is missing on Working Scientifically: Measuring, Recording and Risk, or which topic to write up next.

Build a full practice pack.