GCSE Physics Essentials includes Energy (Physics); Electricity (Physics); Particle Model of Matter (Physics); Forces (Physics); Atomic Structure (Physics); Waves (Physics); Magnetism and Electromagnetism (Physics); Space Physics (Physics); Physics Required Practicals and Uncertainties (Physics); Physics Equations: Recall, Rearrangement and Application (Physics); Circuits, Resistance and Components (Physics); Mains Electricity, Power and Energy (Physics); Motion: Speed, Velocity and Acceleration (Physics); Forces, Newton's Laws and Momentum (Physics); Pressure, Moments and Levers (Physics); Energy Stores, Transfers and Calculations (Physics); Efficiency, Power and Energy Resources (Physics); Wave Properties and Behaviour (Physics); The Electromagnetic Spectrum (Physics); Density and the Particle Model of Matter (Physics); Particle Motion, Gas Pressure and Temperature (Physics); Magnetism and the Motor Effect (Physics); Electromagnetic Induction and Transformers (Physics); The Solar System, Orbital Motion and Satellites (Physics); Red-shift and the Expanding Universe (Physics); Atomic Structure and the Development of the Model (Physics); Radioactivity, Half-Life and Nuclear Uses (Physics).
Method recap - Physics Required Practicals and Uncertainties
- State the independent, dependent and control variables for the practical in question before describing the method, and give the range and interval of the independent variable, for example masses from 1 N to 5 N in 1 N steps.
- Choose apparatus by resolution and justify it: a metre rule reading to 1 mm rather than to 1 cm, a digital ammeter reading to 0.01 A, a balance reading to 0.01 g. Say why the resolution matters for the size of the quantity being measured.
- Reduce random error by repeating and taking a mean, and reduce systematic error by checking the instrument reads zero before use, for example zeroing a newtonmeter held vertically or checking the ammeter reads zero with the circuit open.
- Calculate uncertainty from repeats as half the range: uncertainty = (largest value - smallest value) / 2, quoted as the mean plus or minus that value.
Worked example - Physics Required Practicals and Uncertainties
A student measures the resistance of a wire five times: 4.8, 5.0, 5.1, 4.9 and 5.2 ohms. Calculate the mean, the uncertainty and the percentage uncertainty.
- Add the readings: 4.8 + 5.0 + 5.1 + 4.9 + 5.2 = 25.0 ohms.
- Divide by the number of readings: 25.0 / 5 = 5.0 ohms, so the mean resistance is 5.0 ohms.
- Find the range: largest minus smallest = 5.2 - 4.8 = 0.4 ohms.
- Uncertainty = half the range = 0.4 / 2 = 0.2 ohms, so the result is 5.0 plus or minus 0.2 ohms.
- Percentage uncertainty = (0.2 / 5.0) x 100 = 4 percent.
- Interpret: a second wire measured as 5.1 plus or minus 0.2 ohms overlaps this range, so the two results cannot be said to be different.
Question 8 - Physics Required Practicals and Uncertainties
4 marks
Describe how a student could measure the density of a small irregular stone. Include the apparatus and one precaution.
Answer and mark scheme
Mark scheme for Question 8 [4 marks]| Question 8[4 marks] |
|---|
| Answer or working | Marks |
|---|
| measure the mass of the stone using a balance reading to at least 0.1 g | 1 |
| measure the volume by displacement, lowering the stone into a measuring cylinder (or eureka can) containing a known volume of water and recording the new volume | 1 |
| volume of stone = final volume - initial volume; then density = mass / volume | 1 |
| precaution, read the volume at eye level from the bottom of the meniscus, and make sure the stone is fully submerged and no water splashes out | 1 |
Question 9 - Physics Required Practicals and Uncertainties
3 marks
A student obtains a value for the specific heat capacity of aluminium that is 15 percent higher than the accepted value. Explain the most likely cause and state whether it is a random or a systematic error.
Answer and mark scheme
Mark scheme for Question 9 [3 marks]| Question 9[3 marks] |
|---|
| Answer or working | Marks |
|---|
| energy is transferred from the block to the surroundings rather than all of it heating the block | 1 |
| so the energy supplied, measured by the joulemeter or from power multiplied by time, is greater than the energy that actually raised the temperature, and the calculated specific heat capacity is too high | 1 |
| it is a systematic error, because it shifts every result in the same direction, so repeating would not remove it; insulating the block and using a lid would reduce it | 1 |
Method recap - Physics Equations: Recall, Rearrangement and Application
- List the quantities in the question with their symbols and units before doing anything: write down what you are given and what you are asked for, so the right equation becomes obvious.
- Convert every quantity to SI units first: metres, kilograms, seconds, joules, watts, amperes, volts. Convert kilojoules and kilowatts by multiplying by 1000, minutes and hours to seconds, and centimetres to metres by dividing by 100.
- Write the equation in symbols before substituting, because the first mark is for the equation and it is awarded even if the arithmetic later goes wrong.
- Rearrange before substituting, not after, and use the triangle relationship for any equation of the form a = b x c: cover the quantity you want to find.
Question 8 - Physics Equations: Recall, Rearrangement and Application
3 marks
A kettle transfers 180 kJ of energy in 2 minutes. Calculate its power output in watts.
Answer and mark scheme
Mark scheme for Question 8 [3 marks]| Question 8[3 marks] |
|---|
| Answer or working | Marks |
|---|
| converts the units, 180 kJ = 180 000 J and 2 minutes = 120 s | 1 |
| uses power = energy transferred / time, 180 000 / 120 | 1 |
| final answer 1500 W (accept 1.5 kW) | 1 |
Question 9 - Physics Equations: Recall, Rearrangement and Application
3 marks
A student writes: 'A 2 kW heater running for 30 minutes transfers 60 J.' Identify the error, and calculate the correct value.
Answer and mark scheme
Mark scheme for Question 9 [3 marks]| Question 9[3 marks] |
|---|
| Answer or working | Marks |
|---|
| the error is that neither unit was converted; 2 kW is 2000 W and 30 minutes is 1800 s, so the student has multiplied 2 by 30 | 1 |
| uses energy transferred = power x time = 2000 x 1800 | 1 |
| final answer 3 600 000 J, that is 3.6 MJ (accept 3600 kJ) | 1 |
Method recap - Circuits, Resistance and Components
- Identify the circuit type first: in series there is one loop and one path for the current; in parallel the current has more than one path.
- Apply the series rules: current is the same at every point, potential difference is shared between the components in proportion to their resistance, and total resistance is the sum of the individual resistances.
- Apply the parallel rules: the potential difference across each branch equals the supply potential difference, the currents in the branches add up to the total current from the supply, and the total resistance is less than the smallest single resistance.
- Use potential difference = current x resistance, rearranging to current = potential difference / resistance or resistance = potential difference / current, and always work in volts, amperes and ohms.
Question 8 - Circuits, Resistance and Components
3 marks
Explain why the resistance of a filament lamp increases as the current through it increases.
Answer and mark scheme
Mark scheme for Question 8 [3 marks]| Question 8[3 marks] |
|---|
| Answer or working | Marks |
|---|
| a larger current transfers more energy to the filament, so its temperature rises | 1 |
| the ions in the metal lattice vibrate more with greater amplitude | 1 |
| so there are more collisions between the electrons and the ions, which impedes the flow of charge, and the resistance increases | 1 |
Question 9 - Circuits, Resistance and Components
4 marks
A light-dependent resistor is connected in series with a fixed resistor across a 6 V supply, and the output is taken across the fixed resistor. Explain how the output potential difference changes as night falls.
Answer and mark scheme
Mark scheme for Question 9 [4 marks]| Question 9[4 marks] |
|---|
| Answer or working | Marks |
|---|
| as light intensity falls, the resistance of the light-dependent resistor increases | 1 |
| the total resistance of the circuit increases, so the current decreases | 1 |
| the potential difference is shared in proportion to resistance, so a greater share is across the light-dependent resistor | 1 |
| the potential difference across the fixed resistor, the output, therefore falls as it gets darker, and this change can be used to switch a lamp on | 1 |